Subnetting Assignment

In: Computers and Technology

Submitted By robe
Words 433
Pages 2
02/8/2015

Pick a network address from the list below. Everybody must pick a unique network address and number of subnet. Please reply to the Subnetting Discussion Topic under Week 3 Discussions with your selection. Don’t select a network address that somebody else already selected.
For each of them, I need the following information: * The new subnet mask after the subnetting (10%) * The following information for the four subnets identified: * Subnet’s network address (3%) * Subnet’s broadcast address (3%) * Subnet’s range of available IP addresses (4%) * The calculations on how you get to the answers (50%). This is very important. If you don't provide the calculations or the way you get the answer, you will lose 50%.
Your goal is to subnet them with as little subnet as possible but still meeting the requirement. In other word, maximize the number of hosts that is available for each subnet.

26. 134.84.0.0/16 subnetted to 97 subnets and provide information for subnets #1, #8, #65, and #97

134.84.0.0/16

10000110 01010100 00000000 00000000 Network address
11111111 11111111 00000000 00000000 Subnet Mask

The formula to find out how many bits to borrow
2 to the power off 7 = 128 need to borrow 7 bits.

7 bits = 0000001

New

10000110 01010100 00000000 00000000 Network Address
134.84.0.0/16
11111111 11111111 11111110 00000000 Subnet Mask 255.255.254.0 Subnet Mask

#1 Network Address
10000110 01010100 00000010 00000000 Network Address
134.84.2.0

11111111 11111111 11111110 00000000 Subnet Mask
255.255.254.0

10000110 01010100 00000011 11111111 Broadcast Address
134.84.3.255

Available IP Addresses are 134.84.2.1 until 134.84.3.254

#8 Network Address
Convert 8 to Binary =1000
10000110 01010100 00010000 00000000 Network address
134.84.16.0

11111111…...

Similar Documents

Subnetting 1 2 3

...Subnetting 1 2 3 By Adam Chee W.S Ever get stressed out because you know that there would be subnetting question(s) in the next exam you are taking and that these questions easily take up 10 to 20 minutes of your precious exam time? What if there is more than one question? The process of converting the subnet to binary and decimal can drive the unfamiliar insane, not to mention the waste of precious time and brain power which can be utilized for other areas of exam preparation. Let's take a look at a shortcut method that will cut down the time needed to answer these questions without the need for a calculator. Subnet Basics: This article assumes that you know how to perform subnetting in the traditional method but it is important to stress that there are only 3 classes of usable IP addresses which are Class Range Subnet mask Host bit Subnet Class A (127 is reserved for loopback) 255.0.0.0 24 8 Class B 128 - 191 255.255.0.0 16 16 Class C 192 - 223 255.255.255.0 8 24 1 - 126 You must understand and remember this table well in order to master the shortcut. Note: You must borrow at least 2 bits and must leave at least 2 bits The 'Subnet Table' 1 2 3 4 5 6 7 8 Bit Value 128 64 32 16 8 4 2 1 Subnet Mask 128 192 224 240 248 252 254 255 0 2 6 14 30 62 126 254 Bits Borrowed (N) Number of......

Words: 1155 - Pages: 5

Subnetting Chart Class a to Class E

...Subnetting | Default Subnet Mask | CIDR | Up to usable # Hosts | Default Network/Host | Typical Use | Class A: 1 - 126 | 255.0.0.0 11111111.00000000.00000000.00000000 | /8 | 16,777,214 224 -2 | N.H.H.H | Largest block allocation made by IANA | Class B: 128 - 191 | 255.255.0.0 11111111.11111111.00000000.00000000 | /16 | 65,524 216 -2 | N.N.H.H | ISP/Small ISP/large business | Class C: 192 - 223 | 255.255.255.0 11111111.11111111.11111111.00000000 | /24 | 254 28 -2 | N.N.N.H | Large LAN, Small LAN, Smallest multi-host network, "Glue network" (pt-to-pt) | Class D: 224 - 239 | not defined | not defined | not defined | not defined | A multicast network. | Class E: 240 - 255 | not defined | not defined | not defined | not defined | Address range is reserved for future or experimental purposes. | 127 is Loopback | 127.0.0.1 | | | | | 255 is Broadcast | Broadcast Address: All host bits = 1 | | | | | 0 is the Network | Network or subnet address: All host bits = 0 | | | | | Powers of 2 and CIDR Prefix 16,777,214 | 65,536 | 32,768 | 16,384 | 8,192 | 4,096 | 2,048 | 1,024 | 512 | 256 | 128 | 64 | 32 | 16 | 8 | 4 | 2 | 1 | 2(24) | 2(16) | 2(15) | 2(14) | 2(13) | 2(12) | 2(11) | 2(10) | 2(9) | 2(8) | 2(7) | 2(6) | 2(5) | 2(4) | 2(3) | 2(2) | 2(1) | 2(0) |   |   |   |   |   |   |   |   |   |   | 128 | 192 | 224 | 240 | 248 | 252 | 254 | 255 | Length of the CIDR Prefix, which is varied using VLSM (variable length subnet mask). | /15 |......

Words: 275 - Pages: 2

Unit 6 Subnetting Lab 6

...Unit 6 Subnetting Lab 6 Answer the following questions listed. Using the Class B Subnetting Guide, answer the following: Given an IP address of 172.16.8.1 use the guide to get 30 hosts on each of your 2000 networks: 1. What Class is this IP address? B 2. How many bits would you borrow or take? 11 3. What subnet mask would you generate? 255.255.255.224 4. What is the first subnetwork range created? 172.16.0.1 to 172.16.0.30 5. What is the last subnetwork range created? 172.16.255.225 to 172.16.255.254 Given an IP address of 172.16.4.1 use the guide to get 62 hosts on each of your 1000 networks: 6. What Class is this IP address? B 7. How many bits would you borrow or take? 10 8. What subnet mask would you generate? 255.255.255.192 9. What is the first subnetwork range created? 172.16.0.1 to 172.16.0.62 10. What is the last subnetwork range created? 172.16.255.193 to 172.16.255.254 Given an IP address of 172.16.5.1 use the guide to get 100 hosts on each of your 500 networks: 11. What Class is this IP address? B 12. How many bits would you borrow or take? 9 13. What subnet mask would you generate? 255.255.255.128 14. What is the first subnetwork range created? 172.16.0.1 to 172.16.0.126 15. What is the last subnetwork range created? 172.16.255.129 to 172.16.255.254...

Words: 274 - Pages: 2

Subnetting Assistiance

...11000000 as the subnet mask This means, I will be able to use the FIRST 64 ADDRESSES of the defined Network ID (205.32.16.x) 0 – 63 = 64 addresses Network ID 205.32.16.0 (First IP) Broadcast IP 205.32.16.63 (Last IP) Usable IP Range is 205.32.16.1 – 205.32.16.62 (everything in between) Our subnet mask (255.255.255.192) is reusable IF we still have 64 addresses available to assign in our OWNED network range. ALL the subnet will do is define the beginning and end of a network range. BUT 205.32.16.0 – 205.32.16.63 ARE NOT useable as they are assigned to a site! The next site will have to begin at the next available address (205.32.16.64). The size of this site will depend on the assigned sunbet mask! Making better sense? Try your assignment once more with this logic to determine what values you come up with!...

Words: 1080 - Pages: 5

Ip Subnetting

...16.254.1. Each part represents a group of 8 bits (octet) of the address. In some cases of technical writing, IPv4 addresses may be presented in various hexadecimal, octal, or binary representations. The rapid exhaustion of IPv4 address space, despite conservation techniques, prompted the Internet Engineering Task Force (IETF) to explore new technologies to expand the addressing capability in the Internet. The permanent solution was deemed to be a redesign of the Internet Protocol itself. This next generation of the Internet Protocol, intended to replace IPv4 on the Internet, was eventually named Internet Protocol Version 6 (IPv6) in 1995.[3][4] The address size was increased from 32 to 128 bits or 16 octets. This, even with a generous assignment of network blocks, is deemed sufficient for the foreseeable future. Mathematically, the new address space provides the potential for a maximum of 2128, or about 3.403×1038 addresses. The primary intent of the new design is not to provide just a sufficient quantity of addresses, but rather to allow an efficient aggregation of subnetwork routing prefixes at routing nodes. As a result, routing table sizes are smaller, and the smallest possible individual allocation is a subnet for 264 hosts, which is the square of the size of the entire IPv4 Internet. At these levels, actual address utilization rates will be small on any IPv6 network segment. The new design also provides the opportunity to separate the addressing infrastructure of a......

Words: 841 - Pages: 4

Ip Addressing Subnetting

...010101001011000 110101100011010 11010100001011 001010100110 1001010010 11010011 10011000 IP Addressing and Subnetting Workbook Version 2.0 Instructor’s Edition 11111110 10010101 00011011 10000110 IP Address Classes Class A Class B Class C Class D Class E 1 – 127 128 – 191 192 – 223 224 – 239 240 – 255 (Network 127 is reserved for loopback and internal testing) 00000000.00000000.00000000.00000000 Leading bit pattern 0 Network . Host . Host . Host Leading bit pattern Leading bit pattern 10 110 10000000.00000000.00000000.00000000 Network . Network . Host . Host 11000000.00000000.00000000.00000000 Network . Network . Network . Host (Reserved for multicast) (Reserved for experimental, used for research) Private Address Space Class A Class B Class C 10.0.0.0 to 10.255.255.255 172.16.0.0 to 172.31.255.255 192.168.0.0 to 192.168.255.255 Default Subnet Masks Class A Class B Class C 255.0.0.0 255.255.0.0 255.255.255.0 Produced by: Robb Jones jonesr@careertech.net and/or Robert.Jones@fcps.org Frederick County Career & Technology Center Cisco Networking Academy Frederick County Public Schools Frederick, Maryland, USA Special Thanks to Melvin Baker and Jim Dorsch for taking the time to check this workbook for errors, and to everyone who has sent in suggestions to improve the series. Workbooks included in the series: IP Addressing and Subnetting Workbooks ACLs - Access Lists Workbooks VLSM Variable-Length Subnet Mask Workbooks Instructors......

Words: 18750 - Pages: 75

Assignment 2

...NETW204: Assignment 2 (50 points) Each answer is worth 1 point each, 50 questions = 50 total points. Type answers in the appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME | Tiffany Caldwell | Distance Vector Routing Protocols | Question | Answer | 1 | What does RIP stand for? | Routing Information Protocol | 2 | What metric does RIP use for Path Selection? | Hop count | 3 | If the metric used by RIP exceeds this value for a route it is considered unreachable, effectively making this value appear to be infinity to RIP? | 15 | 4 | How often does RIP send updates by default (update timer)? | 30 seconds | 5 | What are the main differences between RIPv1 and RIPv2? | RIPv2 has next hop addressed included in the routing updates, use of multicases addresses in sending updates. | 6 | What is convergence and why is it important? | Convergence is when the routing tables of all routers are at a state of consistency. A network is not operable until the network has converged | 7 | Is RIP considered to be a fast or slow converging protocol? | Slow converging protocol | For the simple 3 router network (Figure 1), fill in the information that would be in each router’s routing table once the network has converged (see example in Chapter 4, pages 192-193). Figure 1 Questions 8-22 (15 points – first one provided) | R1 | | | | HQ | | | | R3 | | Network | Interface | Hop | | Network |......

Words: 867 - Pages: 4

Assignment 2

...appropriate cell; text will automatically wrap. Post your completed assignment to the dropbox. NAME Distance Vector Routing Protocols Question Answer 1 What does RIP stand for? Routing Information Protocol. 2 What metric does RIP use for Path Selection? hop count 3 If the metric used by RIP exceeds this value for a route it is considered unreachable, effectively making this value appear to be infinity to RIP? Yes poison route or infinity metric 15 4 How often does RIP send updates by default (update timer)? 30 seconds 5 What are the main differences between RIPv1 and RIPv2? RIPv2 is classless where you can include subnets in updates 6 What is convergence and why is it important? Speed and ability of a group of internetworking devices running a specific routing protocol to agree on the topology of an internetwork after a change in that topology 7 Is RIP considered to be a fast or slow converging protocol? Slow. IT has to wait for routes to appear   For the simple 3 router network (Figure 1), fill in the information that would be in each router’s routing table once the network has converged (see example in Chapter 4, pages 192-193). Figure 1 Questions 8-22 (15 points – first one provided) R1 HQ R3 Network Interface Hop Network Interface Hop Network Interface Hop 172.15.0.0 Fa0/0 0   Subnetting and Assigning Addresses Figure 2. Addressing......

Words: 690 - Pages: 3

Subnetting Made Simple

...Subnetting Made Simple IP Subnetting without Tables, Tools, or Tribulations Larry Newcomer The Pennsylvania State University York Campus Abstract Every networking professional should have a thorough understanding of TCP/IP subnetting. Subnetting can improve network performance by splitting up collision and broadcast domains. Subnets can reflect organizational structure and help support security policies. WAN links typically join different subnets. Subnets can define administrative units and hence support the structuring and delegation of administrative tasks. Unfortunately, mastering subnetting can pose difficulties for both professionals and students because of the binary mathematics that underlies the technology. While it is imperative to present subnetting concepts in terms of the underlying binary representation, most texts also present subnetting procedures in binary terms. Such an approach can make it difficult for students to learn how to actually carry out subnetting without tables or other reference materials, even when they understand the basic concepts. This paper presents a simple, alternative method for understanding and implementing subnetting without software, calculators, tables, or other aids. The only knowledge of binary arithmetic required is familiarity with the powers of 2 from 0 to 8 (2x for x = 0, 1, …, 8). With a little decimal arithmetic thrown in, the whole process is simple enough to be carried out mentally. This paper assumes the......

Words: 7956 - Pages: 32

Subnetting Exercise

...Subnetting Exercise Create 7 subnets from the following Class C IP address: 194.27.56.0 subnet mask: 255.255.255.0 Answer the following questions and upload your answers to blackboard. See the next page for an example of how to perform the exercise. 1. How many subnets? 2. How many hosts per subnet? 3. What is the new subnet mask? 4. What is the block size? 5. Create the subnet table. 6. What are the useable subnet address ranges?   Example Create 2 subnets from the following Class C IP address: IP Address: 192.168.1.0 Subnet mask: 255.255.255.0 How many subnets? Steal enough bits from the fourth octet to acquire the desired number of subnet. 2n where n equals 2 - 11000000 22 = 4 subnets (Note useable subnets are 22 - 2 = 2 usable subnets), so stealing 2 bits is enough. How many hosts per subnet? 2y – 2 = number of hosts per subnet. Where y is the number of unmasked bits, or the zeros bits in the fourth octet. - 11000000 26 -2 = 62 hosts per subnet What is the new subnet mask? 11111111.11111111.11111111.11000000 - 255.255.255.192 What is the block size? 256 – subnet mask = block size 256 - 192 = 64 What are the blocks? Start at zero and add the block size to the number to get the next number. Stop when you reach the block size. 0, 64, 128, 192 Create the subnet table. Subnet 0 64 128 192 First Host 1 65 129 193 Last Host 62 126 190 194 Broadcast 63 127 191 255 What are the useable subnet......

Words: 289 - Pages: 2

Subnet Assignment

...CMIT 265 Subnetting Assignment Subnetting Assignment: 215.251.145.0/24 subnetted to 46 subnets and provide information for subnets #1, #4, #5, and #46 Step 1: Convert the network address to binary 215.251.145.0/24 is a class C address with a subnet mask of 24 bits of ones First Octet 128.64.32.16.8.4.2.1, 128=1, 64=1, 32=0, 16=1, 8=0, 4=1, 2=1, 1=1 215 = 11010111. Second Octet = 128.64.32.16.8.4.2.1, 128=1, 64=1, 32=1, 16=1, 8=1, 4=0, 2=1, 1=1 251 = 11111011 Third Octet = 128.64.32.16.8.4.2.1, 128=1, 64=0, 32=0, 16=1, 8=0, 4=0, 2=0, 1=1 145 = 10010001 Fourth Octet = 0 11010111.11111011.10010001.00000000 Network address Step 2: Convert Subnet mask into binary First Octet 128.64.32.16.8.4.2.1, 128=1, 64=1, 32=1, 16=1, 8=1, 4=1, 2=1, 1=1 255 = 11111111 Second Octet 128.64.32.16.8.4.2.1, 128=1, 64=1, 32=1, 16=1, 8=1, 4=1, 2=1, 1=1 255 = 11111111 Third Octet 128.64.32.16.8.4.2.1, 128=1, 64=1, 32=1, 16=1, 8=1, 4=1, 2=1, 1=1 255 = 11111111 Forth Octet = 0 11111111.11111111.11111111.00000000 Subnet mask Step 3: Calculate the subnets required 46 subnets required per instructions: Use the formula 2 to the power of X to find out how many bits to borrow from the subnet mask. 2^5= 32 and is insufficient to cover the subnets required so, 2^6 = 64 x is 6 we need 6 bits from last octet of the subnet mask to cover our subnets. I need 46 subnets but I have total 64 available so that leaves me with; 64-46 = 18 extra subnets to use at a later date.......

Words: 1170 - Pages: 5

Ip Subnetting Project

...This is newest updated file from today. See below. IP Subnetting Project XUMUC is has the WAN links in place to the new locations in the Houston Region. XUMUC currently has 2 other Regions San Francisco and Denver. Originally, XUMUC was only in one region (San Francisco). The previous consultant did a poor job with the integration resulting in a poor IP address scheme as a result routing tables at the summarization points and at the San Francisco Campus are very large. In addition, no VLAN structure was developed to isolate broadcast traffic. There are 4 main departments in XUMC: sales, finance, human resources, and research and development. Also, there has been some concern that the WAN transport was not able to accommodate the network traffic. The XUMC sales team has added a call center with hours of operation from 9AM-9PM EST. Access to the call center network should be restricted after hours. The research and development department has (3) unique special projects which will require over 1000 devices to be enabled to use IPV6. A new network should be created for this area. Finally, all addresses in the network are statically assigned resulting in high administration overhead when changes are needed XUMC would like this changed to lower administrative overhead. The Board of Director meet and decided to add a Security Analyst role to the team. The new Security Analyst has request the access restrictions be documented. The Finance Department should have......

Words: 526 - Pages: 3

Subnetting and Ipv4 Addresses

...Project Description Implement an appropriate addressing scheme, to subnet an IP address for different sized subnets. Introduction I have undertaken this project for the module network models and technologies. The project requires me to implement addressing schemes and to subnet an IP address for different sized subnets. The following topics will also be discussed: * Binary * HEX & decimal number systems * Octet, IP Address, IPv4/IPv6 * Subnet Mask * Network and Host IDs * Address Classes, classful and classless address schemes * Minimising wasteful use of IP addresses * CIDR * Subnetting * VLSM * Health and Safety * Evaluation * Bibliography Binary Computers see things in terms of binary. In binary everything is described as having two values or states: on or off, true or false, 1 or 0 and yes or no. A light switch could be regarded as a binary system, since it is always either on or off. As complex as they might seem computers can be regarded as a box full of light switches. Each switch is called a bit which is short for binary digit and a computer can turn each of these bits on or off. The computer describes 1 as being on and 0 as being off. By itself, a single bit is kind of useless, as it can only represent one of two things. Imagine if you could only count using either zero or one. Alone, you could never count past one. On the other hand, if you got a bunch of friends together who could also count......

Words: 2448 - Pages: 10

Subnetting Practice Worksheet

...Subnetting Practice Worksheet For each of the following IP addresses and subnet masks find; 1. The network Class. 2. The network, subnet, and host portions of the address. 3. Subnet number. 4. Number of hosts in the subnet. 5. Number of subnets in the network. 6. Valid IP address range for the subnet. 7. Broadcast address for the subnet. 10.200.10.18, mask 255.192.0.0 172.31.100.100 , mask 255.255.224.0 192.168.15.150, mask 255.255.255.192 10.100.18.18, mask 255.240.0.0 172.31.200.10, mask 255.255.240.0 192.168.100.100 , mask 255.255.255.248 172.31.50.50 , mask 255.255.252.0 10.150.200.200 , mask 255.254.0.0 26.137.205.172, mask 255.248.0.0 168.31.140.14 , mask 255.255.240.0 10.1.1.1 , mask 255.248.0.0 172.16.1.200 , mask 255.255.240.0 172.16.0.200 , mask 255.255.255.192 1. , mask 255.0.0.0 172.31.50.50 , mask 255.255.254.0 Given this Class B network number, 172.31.0.0 , find the best subnet mask and list the subnet numbers if the network requires at least 35 subnets each with a minimum of 400 hosts. Given this Class C network number, 192.168.8.0 , find the best subnet mask and list the subnet numbers if the network requires at least 12 subnets each with a minimum of 10 hosts. Given this Class A network number, 10.0.0.0 , find the best subnet mask and list the subnet number sequence if the network requires at least 70 subnets each with a minimum of 1400 hosts. Given this Class C network......

Words: 404 - Pages: 2

Subnetting Made Easy

...SUBNETTING MADE EASY [pic] [pic] IP Classes The class system has become "old" in the ever demanding Internet paradigm, it has been (partially) replaced by CIDR system, which allows more efficient and practical allocation of IP addresses for the need of smaller networks. Nevertheless, it is important to know and understand what class system is and how it works, which has been the backbone of the IP. IP addresses have been classified into 5 classes and special purpose addresses, depending upon the value in the first octet. Viz- • Class A - This is a class for very large networks, such as IBM which holds IP addresses in the range - 9.0.0.0 - 9.255.255.255. (almost 16,777,216 IP addresses). First Octet - - The first octet is between 1 to 126. (Starts with binary bit - 0). Network Address - The n/w address is denoted by first 8 bits or first octet. Host/Node Address - Host address is denoted by last 24 bits or last 3 octets. This Network-Host IP configuration for class A can be shown as - network.host.host.host and each can have 1 to 3 decimals. Thus forming 126 network addresses (27 - 1) and each of them capable of having 16,777,214 (224 -2) host addresses. • Class B - This is a class for medium-sized networks. First Octet - - The first octet is between 128 to 191. (Starts with binary bits - 10). Network Address - The n/w address is denoted by first 16 bits or first 2 octets. Host/Node......

Words: 833 - Pages: 4

Will It Snow For Christmas? | GET IT NOW | 更新至10集 黄金神威 第二季动画,历史,冒险2018-10-08(日本)日本