Free Essay

Lan Paper

In: Computers and Technology

Submitted By wayne1966
Words 265
Pages 2
Robert W. Ramirez
LAN Topologies
IT/240
Carlos Zapata
May 31, 2014

LAN Topologies
Case Project I
The changes in equipment that would be required to bring Old-Tech Corporation up to date and solve the shared bandwidth problem would be to change their network scheme. To go from a Star topology to and extended star topology, which their logical topology would be a ring.
We would have to buy five wireless nic-cards to start to accommodate the cabling issue in the warehouse as well as a wireless access point and a wireless router.
Case Project II
EBiz.com would do well with a Switched Logical topology using a physical star topology.
The Network will be Server based running four or five servers each with a certain task. The network will host at least 250 computers not including the servers with room to accommodate at least 50 more computers for future employees. I will implement a number of switches to accommodate the three or more floors that we need to access.
Case Project III
ENorm Inc. would do well with a Mesh Topology; we would use existing wiring closets to run the new cables needed to setup the network. We would also setup the wireless WAN to connect the two offices together. The network will be server based and will have a separate data base server at each location to handle application and data at each location, but accessible to all who need to have access to it. We would have switches in place to handle the necessary bandwidth we decide to go with…...

Similar Documents

Free Essay

Lan Topologies

...LAN Topologies LAN Topologies Ashley Jones University of Phoenix Case Project 2-1 This Case Project explains a network comprised of 50 computers that are connected to 10 Mbps hubs. It goes on to explain the collisions that are occurring when multiple stations send data simultaneously. This description indicates the network is using a logical bus topology because of the 10 Mbps hubs it utilizes. In addition, they are experiencing collisions; in a logical bus topology, data transmitted on the network is viewable by other nodes. The physical topology of this network seems to be an extended star. Since a multiport repeater/hub can have up to 24 ports, they can lay this network out in many different ways. If there is enough office space, they could set up 5 different offices of 10 stations. Each set of 10 would be connected to one 10 Mbps hub and form a physical star. Each of these hubs can be connected to a central hub that is used to extend the network. Case Project 2-2 This Case Project advises of a network that has 200 workstations and four servers connected by multiple switches. The network incorporates a physical star topology because all of its devices come together at a central location. More specifically, this exended star topology allows about 20 workstations to connect to one switch. This setup is repeated multiple times, all with 20 workstations connected. Another switch sits in the “center” of this setup and attaches to one of the switch......

Words: 350 - Pages: 2

Free Essay

Lan Topologies

...LAN Topologies IT240 10/14/12 1. Case Project 2-1 With a network of 50 computers I will use the Ring Topology to upgrade this network. With this type of topology all the devices are connecting in a loop form and the information travels in one direction, thus avoiding collisions. Here the cabling doesn’t terminate, it continually goes from one device to another till it gets back to the original device. It is also easier to manage the network since all the information is passed around the ring in the same direction. 2. Case project 2-2 With that many computer and four servers, I will use an Extended Star Topology. As pointed out in the case project that there are a few switches available here, I will use a central switch and connect the rest of the available switches to it and connect the 200 PC’s to those switches. Switches are good for determining each individual packet’s destination and ensuring that they are delivered to the right device. Note Even though they might have two different uses in some cases, the hubs in my diagram represent the switches. 3. Case project 2-3 * Physical versus logical topology: A physical topology defines how the devices on a particular network are physically connected; logical on the contrast tells us how the systems on the...

Words: 415 - Pages: 2

Premium Essay

Lans and Wans

...hardware and software needed to create and secure the networks. Each location will be set up with its own Wireless local area connection and they will all utilize the Internet to provide a Wide Area connection for the company as a whole. LAN, WAN and Wireless technologies Local Area Networks, or LANs, are a grouping of computers networked together in a generally small geographic area. LAN technology refers to the hardware and software used to create a local area network. The most common wired methods are Ethernet and Token Ring, and WLAN technologies using IEEE 802.11. WAN or Wide Area Network technologies include ATM. TCP/IP, and Frame Relay to connect and transfer data across large distances. Using a cable such as an Ethernet cable computers on a LAN are required to share the network when passing data packets back and forth. Before sending data across the network each computer checks the line for other transmissions. If the line is clear the computer sends the data, if not the computer waits. This method is called CSMA/CD. Wireless LANs or WLANs use RF signals to transmit data across the network. Every computer on a wireless local area network share the same frequency and take turns sending data just like using a cable. Wireless LANs use CSMA/CA to check for an open line of communication to it intended target. The sending device will send out a signal to the receiving device called a Request to Send. If the receiving device is available it will send a clear to......

Words: 1327 - Pages: 6

Free Essay

Lans

...at best—ignoring overhead? d. Suppose now that we wish to build a communications system that will provide the five X-rays of part (c) upon demand; that is, that from the time the X-rays are requested we want them available within 2 s. What is a lowest channel rate that can support this demand? e. The next generation of displays for X-rays is planned for 4096 by 4096 pixels with a 12-bit grayscale.What does the answer to part d become when using this resolution? A multimedia version of a multivolume reference book is being prepared for storage on compact disc (CD-ROM). Each disc can store about 700 MB (megabytes). The input to each volume consists of 1000 pages of text typed 10 characters to the inch, 6 lines to the inch, on 8.5-by-11-in. paper with 1-in. margins on each side. Each volume also has about 100 pictures, which will be displayed in color at Super VGA resolution (1024 × 768 pixel, 8 b/pixel). Moreover, each volume is enhanced for the CD version with 30 min of audio of teleconferencing quality (16,000 smp/s, 6 b/smp). a. How many bits are there on a 700-megabyte CD (1 megabyte = 220 bytes)? b. Without compression and ignoring overhead, how many volumes can be put on one CD? 2.9 2.10 2.11 2.12 2.13 ISBN 0-558-69515-9 Business Data Communications, Sixth Edition, by William Stallings. Published by Prentice Hall. Copyright © 2009 by Pearson Education, Inc. 2.8 / KEY TERMS, REVIEW QUESTIONS, AND......

Words: 9067 - Pages: 37

Premium Essay

Virtual Lan

...Technology for Metropolitan Area Networks Steven S. Gorshe Principal Engineer - PMC-Sierra, Inc. steve_gorshe@pmc-sierra.com ABSTRACT IEEE 802.17 Resilient Packet Ring (RPR) is a promising new technology that was standardized to meet the needs of telecommunications network providers and enterprise data networks. RPR allows substantial reuse of the valuable existing telecommunications infrastructure, while also allowing a greatly simplified means of aggregating packetized data from many customers into the provider’s access and metro networks. The RPR fairness protocol and algorithm insures fair medium access among an RPR’s users. RPR also provides the high reliability that has become increasingly important for enterprise network users. This paper reviews the key aspects of RPR, including medium access control and its fairness mechanism, physical layer options, protection/restoration options, and bridging and routing within and across an RPR. INTRODUCTION The increasing importance and bandwidth demands of enterprise networks in the 1990s generated the desire for a new metropolitan area network (MAN) and wide area network (WAN) protocol. From a data network perspective, the existing protocols lacked a fast, simple Layer 1 mechanism to recover from network faults. From a telecommunications network perspective, it was critical to have a network access technique that would allow maximum re-use of the existing SONET/SDH network infrastructure. These needs were the......

Words: 7303 - Pages: 30

Free Essay

Lan Switching

...roduct Description LAN Switching and Wireless CCNA Exploration Labs and Study Guide Allan Johnson LAN Switching and Wireless, CCNA Exploration Labs and Study Guide is designed to help you learn about and apply your knowledge of the LAN switching and wireless topics from Version 4 of the Cisco® Networking Academy® CCNA® Exploration curriculum. Each chapter contains a Study Guide section and a Labs and Activities section. Study Guide The dozens of exercises in this book help you learn the concepts and configurations crucial to your success as a CCNA exam candidate. Each chapter is slightly different and includes matching, multiple-choice, fill-in-the-blank, and open-ended questions designed to help you Review vocabulary Strengthen troubleshooting skills Boost configuration skills Reinforce concepts Research topics Packet Tracer Activities—This icon identifies exercises interspersed throughout the Study Guide section where you can practice or visualize a specific task using Packet Tracer, a powerful network simulation program developed by Cisco. Labs and Activities The Labs and Activities sections begin with a Command Reference table and include all the online curriculum labs to ensure that you have mastered the practical skills needed to succeed in this course. Hands-On Labs—This icon identifies the hands-on labs created for each chapter. Work through all the Basic, Challenge, and Troubleshooting labs as provided to gain a deep......

Words: 339 - Pages: 2

Premium Essay

Lan Topologies

...Rodolfo Aybar IT/240 LAN Topologies Scott Perales April 27, 2014 Case 2-1 I would recommend the use of a central server which will ease up the process of controlling the incoming and outgoing data transmission. The central server will help the network not get overloaded with the amount of data packets being received and sent. In relation with the Hubs, it will be beneficiary to update them to be able to hubs with the capacity of 1,000 Mbps. This will also help with the overall network performance. Case 2-2 In this case, I will replace the switches and install routers instead. Routers have a better capability in joining together multiple LAN networks with WAN. Routers serves as a median destination for the network traffic. The routers with these workstations will be able to receive, analyzed the source and potential target, and where every packet will need to be sent to. Switches in this scenario, are not able to separate the broadcast domain like the router could; switches are only able to separate the collision in the domain. A network with only switches (hubs) must instead designate one computer as the gateway to the Internet, and that device must possess two network adapters for sharing, one for the home LAN and one for the Internet WAN. (Mitchell, 2014).  Case 2-3 Logical/physical topology: A logical topology...

Words: 452 - Pages: 2

Premium Essay

Lan Topologies

...transfers between clients and servers. How do you recommend upgrading this network? What interconnecting devices will you use, and what benefit will you get from using these devices? Write a short memo describing the upgrade and, if possible, include a drawing of the new network. This network should have a central server that can control incoming and outgoing transmissions. A central server would stop the entire network from being bogged down because of data packets being sent and received. In addition, the hubs should be upgraded to handle 1000 Mbps. Below is an example of what a smaller version would look like. Case Project 2-2 Two hundred workstations and four servers on a single LAN are connected by a number of switches. You’re seeing an excessive number of broadcast packets throughout the LAN and want to decrease the effect this broadcast traffic has on your network. What steps must you take to achieve this goal? Ideally it’s preferable to probably split it up into one or more workstation subnets (based on say, departments) and then another subnet (or more for a larger enterprise) for the servers. Traffic between the subnets will be routed. This means the broadcasts from workstations won't hamper the servers and vice versa. Case Project 2-3 In Chapter 3, you learn about network topologies and technologies. As preparation, do Internet research on the following topics: ● Physical versus logical topology ● Bus topology ● Star topology ● Ring......

Words: 749 - Pages: 3

Premium Essay

Lan Senarios

...those networked PCs access to one another's hard drives, printers and a shared Internet connection. Components: A. Internet connection B. Modem to transfer the data from the incoming internet connection. C. Router if you want to create multiple networks. D. Hub to connect the workstations on each network. E. Workstations w/ Network interface cards (NIC). F. Printers/Scanners etc.. G. Ethernet cables (preferably Cat 6e). 3. You are the administrator of a client-server environment. What kind of network would you install? How would the pieces and components of this network relate to each other? Define each component of a typical client/server environment. I would either use a LAN, or a WAN network type. For these reasons a LAN would be best for close proximity networking, such as those in the same building, or a WAN for those that are located outside the same building, such as other building to the main hub building. This would give all those involves access to the main servers, as well as communications with each other computer. Components: A. Internet connection B. Modem to transfer the data from the incoming internet connection. C. Router if you want to create multiple networks D. DNS Server E. Server to handle logon/authentication. Most likely Windows Server, with Active Directory. F. File server; a computer attached to a network that has the primary purpose of providing a location for shared disk......

Words: 530 - Pages: 3

Free Essay

Lan Topologies

...LAN Topologies Jason Smith IT/240 September 7 2014 TAMMY FLEMONS LAN Topologies Case Project 2-1 You have been hired to upgrade a network of 50 computers currently connected to 10 Mbps hubs. This long-overdue upgrade is necessary because of poor network response time caused by a lot of collisions occurring during long file transfers between clients and servers. How do you recommend upgrading this network? What interconnecting devices will you use, and what benefit will you get from using these devices? Write a short memo describing the upgrade and, if possible, include a drawing of the new network. This system ought to have a central server that can control approaching and cordial transmissions. A central server would prevent the whole system from being hindered due to information parcels being sent and acquired. What's more, the center points ought to be moved up to handle 1000 Mbps. The following is a sample of what a littler variant would look like. I think I would use the physical star topology for this setup. Case Project 2-2 Two hundred workstations and four servers on a single LAN are connected by a number of switches. You’re seeing an excessive number of broadcast packets Throughout the LAN and want to decrease the effect this broadcast traffic has on your network. What steps must you take to achieve this goal? Utilizing an expanded star topology would diminish the impacts of the......

Words: 677 - Pages: 3

Premium Essay

Lan Lan Lan Aland

...LAN Operating Systems Scenarios Read the three scenarios below and answer the questions that follow each scenario. 1. You are the network administrator for a new company that has 10 users and that plans to add 5 more users within a year. The files need to be accessed by all 10 users, and each user must have different security rights. What kind of network would you install? How would the pieces and components of this network relate to each other? Define each component. 1.2. I would install a client/server network on a local area network (LAN). Every computer connected to the network would have a network interface card (NIC) and through the use of Ethernet cables, connect to the company server. Users would be able to store files and share company resources through the server. Implementing a Windows based operating system on the server will allow for the network administrator to assign different security rights and privileges to different users. I think that for this particular situation I would set up an extended star network. I would choose this one because the business is relatively small and plans to grow, this type of network setup is very easy to add users onto and also still provides the access restriction needed for lower level employees and the ease of access for higher level employees without them being able to see what the other is able to access. “As the name implies, this topology is a star of stars. A central device, usually a switch, sits in the middle...

Words: 583 - Pages: 3

Free Essay

Lan Wan

...Local are networks (LAN) is a computer network covering a small geographic area, like a home, office, school, or group of buildings. Has a High speed (1000 mbps) Tends to use certain connectivity technologies, primarily Ethernet and Token Ring. LANs tend to have fewer problems associated with them, as there are smaller numbers of systems to deal with. Wide area network (WAN) is a computer network that covers a broad area. It does have slower speeds of about 150 mbps. WANs tend to use technologies like MPLS, ATM, Frame Relay and X.25 for connectivity over longer distances Differences between (LAN) & (WAN) (LAN) is typically owned and managed by a single company or organization. LAN also experiences fewer data transmission errors and overall fewer problems as a whole as opposed to WAN. WAN has a high cost maintenance and lower bandwidth. In conclusion the major differences are going to be cost, efficiency and coverage Describe common physical topologies and a logical topology : Physical topology refers to how the network is wired it can be either a ring topology where all the hosts are connected together or a bus topology where there is a network medium and each host connects to that medium by wire. A logical topology in the other hand governs how the network is going to work. For example all the hosts in the network are connected through a central connecting point that’s the physical topology however the way the protocols and hardware are designed to......

Words: 273 - Pages: 2

Free Essay

Lan Emulation

...LAN Emulation Overview This overview gives a high-level description of LAN Emulation (LANE). LAN Emulation (LANE) Implementation of LANE makes an ATM interface look like one or more Ethernet interfaces. LANE is an ATM service defined by the ATM Forum specification LAN Emulation over ATM, ATM_FORUM 94-0035. This service emulates the following LAN-specific characteristics: • Connectionless services • Multicast services • LAN media access control (MAC) driver services LANE service provides connectivity between ATM-attached devices and connectivity with LAN-attached devices. This includes connectivity between ATM-attached stations and LAN-attached stations and also connectivity between LAN-attached stations across an ATM network. Because LANE connectivity is defined at the MAC layer, upper protocol layer functions of LAN applications can continue unchanged when the devices join emulated LANs. This feature protects corporate investments in legacy LAN applications. An ATM network can support multiple independent emulated LAN networks. Membership of an end system in any of the emulated LANs is independent of the physical location of the end system. This characteristic enables easy hardware moves and location changes. In addition, the end systems can also move easily from one emulated LAN to another, whether or not the hardware moves. LAN emulation in an ATM environment provides routing between emulated LANs for supported routing protocols and high-speed,...

Words: 896 - Pages: 4

Free Essay

Lan Consultation

...LAN Consulting Plan IT/240 February 26, 2012 James (Garrett) Miller LAN Consulting Plan Data Assurance: 1.      Backup system: a.     Type? Backup of data will be done with the Norton 360 version 6.0 antivirus protection suite provided backup utility, Symantec Backup Exec. There are two types of backup for this network. The first is a digital tape drive backup that is located on site for intermediate recovery based on the disaster conditions. The second backup is a mirror backup on a bank of servers at an external site to ensure the security of the data in the case of total disaster of the network site. b.     Backup Schedule? The backup schedule will be determined by the importance of the information. Business critical information will be backed up at the completion of the task. A scheduled mirror backup will be done daily during the off business hours. c.     Backup Data Storage plan? The first backed up data will be stored on an independent server drive using RAID at the main site location for ease of access in the case of an independent component failure. The second backup will be also use RAID and be stored at a different graphical location than the network. Data Integrity: 1.      Antivirus system: a.     Type? Norton 360 version 6.0 antivirus program is installed at each geographical location including the offsite backup of the network. This security protection will provide virus protection, spyware protection, and scan incoming and outgoing......

Words: 1841 - Pages: 8

Free Essay

Lan Topologies

...LAN Topologies Lord Bones IT240 Jan 01, University of Phoenix - AXIA College LAN Topologies With this assignment I will discuss some topologies of a LAN as requested by questions 11, 12, and 13, chapter three from the textbook Local Area Networks. A “LAN (Local Area Network) topology is the appearance or layout of a network” (Regan, 2006). There are two forms of topologies of a network, namely, the physical- and logical topology with each its own types of topologies. The physical topology is what someone can see with his or her own eyes, i.e. a workstation, servers, cables, etc. while the logical topology is the dataflow of the network, how the data is moving from one point to another (Regan, 2006). In the following I will describe two physical topology types and one logical topology type, following the scenarios in the question’s mentioned above. In the first scenario there are four servers in the network with no hub present. The first (A) server is connected to the second (B), third (C), and the fourth (D). The second is connected to the third and fourth, while the third is connected to the fourth. (See figure 1.) This type of physical topology is called a Mesh Topology. A Mesh Topology is a topology where “every computer is linked to every other computer” (Regan, 2006). With this type of topology there is no hub or a similar device present. Also this type is difficult to install and certainly when it has to be reconfigured when a new computer is added to the......

Words: 817 - Pages: 4

Conflict between Trade Unions and Management | Black Dandy - Mode als politisches Statement | Construire un couple conscient